Go Back   Ducati Forum > Ducati Panigale Forum > Ducati 1299

Ducati 1299 Ducati 1299 Forum - Ducati 1299 Panigale Superbike Motorcycle Forum


Thanks Tree2Thanks
Reply
 
LinkBack Thread Tools Display Modes
Old May 2nd 2015, 01:42 PM   #1
Member
 
Joined: Apr 2012
From: California

Posts: 97
Thanks: 34

DP rearsets install instructions anyone??

Bought the DP rearsets from a forum member, but they didn't come with install instructions, and it isn't immediately clear what screws where. Setting up for GP shift.
McLaren12C is offline  
 
Old May 2nd 2015, 01:53 PM   #2
Senior Member
 
Joined: May 2012
From: MEXICO

Posts: 190
Thanks: 58

PM me with an e-mail address and I'll send you the instructions
Thanks from McLaren12C
xpercad is offline  
Old May 2nd 2015, 03:44 PM   #3
Senior Member
 
Joined: Sep 2013
From: Chicago, IL

Posts: 1,068
Thanks: 233

What setting are you going to have them at (High or Low)?
BadBoyBeltran is offline  
Old May 2nd 2015, 04:21 PM   #4
Member
 
Joined: Apr 2012
From: California

Posts: 97
Thanks: 34

Low
McLaren12C is offline  
Old May 2nd 2015, 04:28 PM   #5
Senior Member
 
Joined: Sep 2013
From: Chicago, IL

Posts: 1,068
Thanks: 233

I have mine on low.

One thing that I did after several trials is had the linkage (Item 5 on the instructions) the shortest. This is with the locknut.

It took me several tries to get it smooth, and now it shifts well and it's easy to find Neutral.

Make sure you Loctite everything (except for the locknuts), and keep the alignment of the shifter to the tranny the same (you probably have to take it out). There's a dot that aligns to a notch.

Holler if you come across issues.
BadBoyBeltran is offline  
Old May 2nd 2015, 05:15 PM   #6
Member
 
Joined: Apr 2012
From: California

Posts: 97
Thanks: 34

Thanks all!! Especially Xpercad for sending a scan of the instructions
McLaren12C is offline  
Old May 2nd 2015, 05:37 PM   #7
Senior Member
 
Joined: Sep 2013
From: Chicago, IL

Posts: 1,068
Thanks: 233

I just saw my recommendation on the linkage and your wanting to set-up yours to GP shift.

I have mine on normal shift @@
BadBoyBeltran is offline  
Old May 2nd 2015, 09:15 PM   #8
Senior Member
 
leftcoast32's Avatar
 
Joined: Mar 2014
From: San Marcos, CA

Posts: 493
Thanks: 181

I Ride: '14 Panigale R & '14 Pikes Peak
Don't know if this will help much, these are from back when I first installed them. Mine is set up on normal shift. The Heal Guard on the brake side is now on the lower front hole, there are 2 different ways for it to bolt up..




Last edited by leftcoast32; May 2nd 2015 at 09:59 PM.
leftcoast32 is offline  
Old May 3rd 2015, 08:11 PM   #9
Member
 
Joined: Apr 2012
From: California

Posts: 97
Thanks: 34

How the hell do you get that linkage off? The screw holding the linkage to the trans is behind the clutch fluid intake, and it's all too tight to remove linkage at the spline itself. I'm boned right now.
McLaren12C is offline  
Old May 3rd 2015, 08:42 PM   #10
Senior Member
 
leftcoast32's Avatar
 
Joined: Mar 2014
From: San Marcos, CA

Posts: 493
Thanks: 181

I Ride: '14 Panigale R & '14 Pikes Peak
I think I just unscrewed the shaft from the sensor once the rear of it was disconnected. Sorry, It has been a while since I installed mine.
leftcoast32 is offline  
Reply

  Ducati Forum > Ducati Panigale Forum > Ducati 1299

Tags
install, instructions, rearsets



Thread Tools
Display Modes


Similar Discussions
Thread Thread Starter Forum Replies Last Post
"Riding In" Instructions Marchant Ducati 1199 48 Aug 20th 2014 06:50 AM
Fan install Thamer Ducati 1199 0 Jun 23rd 2014 10:08 AM
Install instructions for superleggera kit. hyperdrive Ducati Superleggera 5 May 14th 2014 09:07 PM
Instructions for adjustment of brake pedal craigslistbuyermn Ducati 1199 1 Jul 26th 2013 01:21 PM
Alarm Instructions carldickson Ducati 1199 4 Nov 11th 2012 11:30 AM


Facebook Twitter Google+ RSS Feed