bolts

Can anyone help me identify this bolt? It's a 75mm M6 (greased) with a point on the end. I have been working on the bike, installing some heat shielding inside the subframe and this fell out of seemingly nowhere. I have no recollection of having removed it and am wondering if it was loose and...

I'm installing the Arrow exhuast on the V4. Instructions say to loosen the rear header bolts... has anyone had to do this on an arrow install or anything similiar. How did you do it... or is there away around this?

I have an '04 Multi and recently picked up a CF chin faring, but it didn't come with the mounting bolts that go into the cases. Ive searched on-line, looked at the parts diagram with no luck, and can't seem to find out where to get some. If anyone knows, please drop me a link or a business name...

I just wanted to get a bit of advice on using Ti bolts in aluminium I use an anti-seize compound when using Ti bolts but on a couple of areas I'd like to use a thread locker. I know a few here have good knowledge of the science of metals and would appreciate your advice.

Dear Members I was really suprised to see that there are some members left in the forum which are replacing OEM bolts on their bikes :) I am still shedding weight on my three Panigales.... Next step: I want to replace the M8x32 10.9 high tensile bolts in the two cylinder heads (#7 in...

Hi Guys, I felt so defeated this weekend... I was trying to install my radiator guard I had purchased for my 1199 Panigale S and the 2.5mm hex screw came out with ease on one side and the other side has been stripped. I tried spraying WD40 on the bolt but no luck any suggestions? Also, I...

I know there are a few of you on here that have ProTi bolts. How long did the shipping take? They told me it should've arrived in the US in 2 days, but it's been about a month. Tracking on postserv.post.gov.tw says "departure from outgoing office on the 12th" and USPS says "not trackable"...

Hi all. Giving the bike a good once over to order a load of new parts (already spent £509, have a fair chunk more to order!) and noticed the fork bottoms are really tight. Is this normal? https://imgur.com/gallery/XdNLbAj

There are still some bolts on my Panigales that I haven't replaced with Ti. Due to the fact that I did not find any seller for the silly two-sided steel bolt (picture attached to this post), I decided to manufacture them. There are about 10-14 bolts on the Panigale, dependent on the setup...

After the 1199 1299 series of bikes there was a common problem of bolts coming loose so I think the factory have taken this on board . The new V4 seems to have red Loctite on everything which is making things really painful with taking things apart . I have attempted to remove the rear sub...

Anyone on here can share the torque table for the nut and bols tightening for V4 in Newtons? My chain is too long now, but i need the value to unlock the rear wheel hub and then tighten it again, after i set the right chain length. Thanks in advance. Sergio

Here is a pic from a microfiche of my bike part. The part Im talking about is number 12 in the microfiche. I was trying to insert the bursig slug into my 1299 today. The slug was supposed to replace that big bolt in the microfiche right under #10. While trying to pull out the stock bolt I...

Hi all, My 1199 is now leaking a fair bit when under hard use from the horizontal rocker cover. I had replaced the gasket previously on the vertical one and sealed it up with extra gasket goo. However the horizontal one is buried under loads of junk. Any quick way of accessing the bolts...

This summer I ordered a V-cylinder heat shield from Tamburini. Fittment is pretty bad, needed a lot of grinding. I used Phl's H-cylinder bolts, made 4 aluminium spacers, and bought 4 podium racing bolts. To the Webmaster of this site: Please allow uploading pictures as it was before in the...

Hi, Does anyone know the size, length, and pitch of the four bolts that are required to install the passenger footpegs? I don't have them and need to order some online.

If anyone has any laying around I'll take them

The first 1199 Panigales have a Bosch ABS unit with two different Banjo bolt sizes. Two bolts are M10x1, the other two are much bigger. Does anybody know the size or where to source these in Titanium? Thank you guys in advance!

Anyone knows the lenght of the M5 0.8 bolts that attach the mirrors to the frame of the 1299?

I've been looking all over for these guys! I need one bolt with both front and rear washer. If you have more than one I'll graciously take them off your hands as well.

I hate working on the "rear subframe lower mounting bolts". It's diffcult to find the right torx bit tool and there is not much room for maneuvering :( I wanted a lighter, cheap and more practical solution. Easy: Bought two standard allen M8 bolts with 70mm length (in my case Titanium)...