fitting

My RB Shift assist arrived today. Nice of RB not to include a shift rod! but never mind. Has anyone on here fitted and set one up, Just looking for pointers before I start Thanks

I have had the full Akrapovic exhaust system fitted to my V4S which looks and sounds amazing, but the connectors for two cables from the Ohlins rear shock are just open to the elements and look a bit 'out of place'. Should they be connected behind the rubber manifold that they run in to? What...

Hey guys, I recently fitted a full Akrapovic system to my 1299S and thought I'd share some words of wisdom that they don't tell you in the install guide. In no particular order: Before starting, remove the rear subframe, both sides of the fairings and the fan assembly at the front underside...

Hi This morning I took my bike to Hathaway Transport to have my bike shipped to Estoril. Due to new EU regs trucks can be taller than 4m so the stillages are shorter meaning we have to take the screens off. So my advice is if you are a Panigale owner ask for an orange stillage which doesn't...

So I'm in the process of fitting Armour bodies on my 1199... Top fairing and tail section was a piece of cake! however the side panels require more work... It looks like I'll need to remove the plastic housing for all the wires and ecu etc... Anyone can share any good info on the job? Thanks in...

Complete noob question. How do you fit this? Can't find my instructions book and might need to use it later today. The long screws for the pegs, tell me I don't need to take anything off to fit those, classic ducati lol. Just want to say, coming up to 3k miles and this bike in race mode...

Does any one have any useful tips for fitting these. I am at last reaching the end of this year long project, delayed for numerous reasons. I am fitting the Lieb Speed ones which have an extra securing tab in them which clips under the side of the nose fairing at right angles to it. Being carbon...

Was planning on doing it myself but just out of curiousity asked the dealer in PDX how much it would cost. 8 hours labor?! Removing exhaust, radiator, trimming/sanding Skinz.... Really??

has anyone here actually done a self-install on the termi's and left the flapper valve in place? The ebay vid shows it being removed both internally and externally, I think that the 2012 flap stays open when you disconnect the cable but have not had the exhaust off to check. If so theoretically...

Was talking to another member and I gave in and will be adding my rear brake pressure switch. Why not right? This is my custom cable I made for the rear brake using the banjo fitting and original cable.

I have tried to find a thread on this, with no luck. However I am sure I read that this is a real ball ache to fit....is this true.. is this true, any advice please. thanks

So after some creative work with a Dremel, I've finally got one of these fitted: GIVI 3D601 TANKLOCK - Soft Luggages I preferred the look of the Givi to the SW-Motech equivalent, but I had to buy the SW-Motech Quicklock evo to get the adapter plate to attach the Givi adapter plate. I believe...

Trying to fit a set of CRC race fairings to 1199 base. Not sure how the top air tube is meant to fit in. Read another post they need to be trimmed first because it was designed to fit the S model. Anyone have any pics of this fitted or how they modified it?

Well holly cr@p!!, NOT a 5 minute job, even for a seasoned mechanical engineer and racer, the booklet supplied by Ducati/termi is a must, I have refitted the glass, the heat protection supplied in the kit is a .... to fit, used on the bottom rear of the tank and also to protect the ECU, getting...

I noticed a number of very interesting things: 1) A snapped upper fairing slot that had been painted over. 2) The RHS mounting bolt for the nose cone was completely loose and ready to jump out. I'm sure this looseness accounts for both a rev dependant buzz/vibration I was hearing and the...

Sorry if this has been posted elsewhere, Has anyone fitted their R&G Tailtidy yet? If so how difficult was it? Did you encounter any problems? Where's the pictures!?

Thought it might be good for a thread for people to share their experiences on fitting DP parts to their bikes. I did the first three today, carbon heel guards (2 minutes), carbon hugger (20 minutes due to the recessed screw!) and finally clutch cover (30 mins after deciding not to take off...