header

Looking to buy rear exhaust header after mine cracked today.

Recently changed my rear header pipe on my 1299 the one that curls under the seat. The original one cracked at the engine. So I replaced it with a stock header pipe. Everything went very smooth. I turned on my bike and it shows a check engine light. Also after just a minute right at the pipe...

I'm installing the Arrow exhuast on the V4. Instructions say to loosen the rear header bolts... has anyone had to do this on an arrow install or anything similiar. How did you do it... or is there away around this?

Hi, Does anyone know if the 1299/959 heat shield for the rear header fit on the 1199?The 1199 heat shield screws on to the header itself and I keep having to replace the rubber grommets regularly and the plastic is melting. I know the 1299 version bolts onto the rear frame and think its a...

Was at Barber for some running in circles. First two sessions went great. Was really confident and had tons of fun. End of the second session, exiting the Museum Turn, bike gets crazy loud. I raise the hand and roll out. Park it. Back in the paddock: Loaded back up: Then i was in...

Curious if this was happening to anyone else... Behind the radiator on the header there is a torque screw (in the US). The weld holding the thread in somehow blew. The first time this happened (on the track) the heat or flames from the exhaust melted my kickstand sensor causing my bike to...

Yes pulled off the exhaust header and found this shocking mess :eek:

Looking for titanium headers that will mate to my existing termi cans. Is there such a thing BESIDES the D75 lobster tail pipes by motocorse?...or any other header+heatshield system that costs 5k for that matter.

The exhaust valve at the outlet of the headers for noise control(?), what's the consensus? Remove it or leave it as is with the spring holding it open? Anyone tested it both ways with dyno charts showing the differences? Personally I see it as an obstruction that should be removed.

Just a heads up. My bike just had the rear header snap at the flange AGAIN! Ducati North America denied a warranty claim on it, stating that because I have a non Ducati authorized part on it (the Termignoni front exit slipon) they were denying the claim. I pointed out that for 30 years...

im taking the headers to be ceramic coated..the front header looks a pain to remove, any pointers or tips?

Updated with Photos... Cracked header at 7,680 miles. On my evening commute, about 3 minutes from my dealership, my bike started to make a HORRIBLE sound and hot air started pouring out of the right side of my bike... Pulled into my dealership and you could see that the rear cylinder header...

Just saw that on FastFrank's Facebook site. He's in Daytona now. Bike is not his and I'm not sure if it's the akra or stock, but I guess akra.

Heading out for Sunday morning ride, approx 5 miles after I set off and still in warm up mode the bike sounded very rough! Thought I had lunched the motor! Pulled over to take a look at the bike and the exhaust down pipe had cracked clean through! (Bike is 3 months old and has done 3100...

Just wondering, not the most economical solution, but will it work?

Does anyone know what is this? http://m.subito.it/vim/79568297.htm I'm not quite sure if it's beneficial for the delivery power. Thanks

Who has the best price on the Termi PRO header????

Can someone confirm that if the Termignoni headers have the 12 or 18 mm Lambda bungs? (not the oem header). Race system. Thanks

Thanks to Hawaiiduc for reminding about the Superstock 1000 Race from Assen. For those that haven't watched the 2013 STK 1000 season, the Panigale's have been consistently fighting at the front in STK 1000 vs. their mid-pack showing in SBK. These bikes are far closer to what is on showroom...

After I had my 1k service and install of the Termi's I took the bike out for some fun, spirited riding (I drove the .... out of it). I guess I got it pretty warm and jiggled a bunch of screws loose because the header cover had basically lost all of its screws and was resting on the top of the...