plate

Good day, I am trying to trace the wires for the running light and tail light. The running light is more important for Pa inspection. It is the yellow on the harness. The brake light works so red and black are fine. Traced back to first plug under the 750 Dark black cover on right...

I searched the forums and I found several threads on torque, but I could not find a thread specifically asking what my issue is. I have a 07 1098 S. I recently replaced the clutch pressure plate with the rizoma star pressure plate. If I tighten down the clutch pressure plate bolts to 5 Nm, as...

Hi all I've recently had to change my CW integrated rear unit as the brake light failed in it. When I went to hook everything back up with the new unit I found that my number plate light (also LED aftermarket) now comes on and off. Its not flashing fast to suggest its a voltage regulator...

Monster 696. Unable to fully remove clutch pressure plate after springs removed. Any suggestions?

Its basically a 2 in 1 license plate bracket/fender eliminator AND license plate hiding gadget. Uses a tiny remote control to flip the plate... Here is about what it should look like on a few different bikes (its a digital mockup, you can do this for any bike on 007plate website). The...

$35.00 shipped to the us Mint condition. https://www.dropbox.com/s/n6cbjukadh9gjgz/20180731_204402.jpg?dl=0 https://www.dropbox.com/s/szmlfe2xwnvs8vu/20180731_204512.png?dl=0

while riding yesterday, at one point I applied the rear brake only...and there was no tension on the foot lever, as if all the hydraulic fluid had drained out. That's probably not good, so I pulled over, tried the rear brake again, which then had normal tension and worked fine...except for a...

I was installing my new CNC racing frame sliders and decided to install the Ducabike clutch pressure plate inside my Ducabike clear clutch cover. I removed the ducabike pressure spring ring. Then pulled the stock pressure plate out. Saw I couldnt get the inner bearing out with the sleeve and...

Hi guys. Just bought the CNC racing frame sliders in red and black to replace my Sato Racing ones. And I bought a black ducabike clutch pressure plate to go with the ducabike clear clutch cover and ducabike pressure plate ring. However I after removing the pressure plate I cant seem to get the...

Can anyone help me or give me ideas on what to do about having a license plate holder that will fit with the Termignoni full force undertail exhaust? I know Termi makes a holder but i really want to avoid spending $400 on a freaking license plate holder!

I'm currently filling up parts bins in the garage awaiting the arrival of a 959 Corse (my first Ducati). I've recently been looking at the Ducabike clutch covers. If I change from stock to this then I'd probably want to change the pressure plate too and wondered how awkward/fiddly a job this...

Pressure plate question I recently swapped out my 1299 pressure plate with a ducabike one. I just noticed that the stock pressure plate has 3 metal snap rings at the base where the springs sits on. In ducabike's instruction it did not call for the rings to be used from the stock pressure...

Hi, Is the picture presenting full set of Ducati performance tail tidy?I am curious because I had received only bigger plate holder without smaller one in package as highlighted ..Thanks in advance.

Hello, Does anyone know where you can buy these connectors? I have circled it in red. It is the connector that goes to the rear LED license plate light. Imgur: The most awesome images on the Internet Thanks

Hello, I tried searching the forums for this but it's kind of obscure. Does anyone know where I can get these connectors? It is the connector that goes from the license plate LED to the harness. I have attached a photo of the connector in question. Thanks!

The exchange rate is a big factor in the moto business. With favorable exchange rates we are able to negotiate lower prices for volume and save on shipping. Right now it is the best it has been in a long time. Ducabike Clear Wet Clutch Cover/Pressure Plate Ring Combo: Ducati Panigale...

Hi all, I recently got the Ducabike clear clutch cover kit for my 1299. I also got the pressure plate they make because I thought while I'm in there, why not? It's this piece: Ducabike Pressure Plate My dealer says they should install that piece because you need a special clutch tool to...

The exchange rate is a big factor in the moto business. With favorable exchange rates we are able to negotiate lower prices for volume and save on shipping. Right now it is the best it has been in a long time. Ducabike Clear Wet Clutch Cover/Pressure Plate Ring Combo: Ducati Panigale...

Hi all Done a few track days on the1299 and one issue has come up a few times, sometimes a little dangerously. I have Sidi Vertigo boots which have protection around the heel. It's a bolt on part. This keeps getting caught up on heel guard on the bike which stops me from changing gear. Does...

I'm installing the Ducabike clear clutch cover and inner ring, but I also got their nice clutch plate to go with it (while I got it open I figured why not). Dealer says I should let them install the actual pressure plate because you need a special tool to hold it all together. Is this true...