screw

Hi everyone, I was installing my crg carbon levers the other day and I lost one of the set screws for the plunger. Does anyone know where I could find another one or does anyone know the size? I posted in the WTB section for any damaged levers also so fingers crossed. Thanks for any help in advance.

Curious if this was happening to anyone else... Behind the radiator on the header there is a torque screw (in the US). The weld holding the thread in somehow blew. The first time this happened (on the track) the heat or flames from the exhaust melted my kickstand sensor causing my bike to...

So I came outside to find my 1299 laying on its side. Looks like someone bumped it and it fell over. I have frame sliders so didn't look like there was any real damage until I picked her up. What I found was a screw, nut, and a piece of the frame that was broken off. If you look at the...

Had to happen! Just when going to replace those screws when one of them stuck and the hex slot rounded. Had to go to a track day with the mirrors blocked with tape.... Screw still stuck. Cut a slot with a dremell but cannot torque it out with a flat screwdriver... Access to the screw with a...

CNC Racing Special Seat Screw: 899/959/1199/1299 Panigale $10.35 * The saddle screw machined from solid aluminum alloy with anodized surface next. Kit is composed by one screw. * FREE continental USA shipping on orders over $100. * Outside continental USA, use shipping...

Hi, Did has Ducati Performance Tail Tidy installed recently. It did not align perfectly (carbon top part and light) so I decided to amend it. During removing part by part I found out that one of the screw of the set is broken and of course it was impossible to unscrew it. I believe that was the...

I know this is a long shot but I have a 1995 916 and I'm trying to find the small screw cover stickers ( tamper seals) that came on them. It's about a 3/8" round sticker. White with the blue Magnetti Marelli logo on it. I have scoured the internet and can't find any reproduced for restoration...

Hello, I mistakenly removed a special screw as I attempted to install an engine slider on my 2012 Ducati Panigale S. I realized my mistake when oil started pouring out of the crankcase! I quickly screwed the fastener back in, but I am not sure how many threads should be showing for correct...

CNC Racing Special Seat Screw: 899/959/1199/1299 Panigale $10.35 * The saddle screw machined from solid aluminum alloy with anodized surface next. Kit is composed by one screw. * FREE continental USA shipping on orders over $100. * Outside continental USA, use shipping...

CNC Racing Special Seat Screw: 899/959/1199/1299 Panigale $10.35 * The saddle screw machined from solid aluminum alloy with anodized surface next. Kit is composed by one screw. * FREE continental USA shipping on orders over $100. * Outside continental USA, use shipping...

Does anybody know the size and the torque for those two pivot bolt screws (#22 on the attached picture)?

I am just gonna leave this right here. Stock engine, Akra exhaust, Tuneboy with lots of tuning, Sprint filter, and MR12.

It appears I lost the little screw that holds the rear brake's fluid reservoir to the little black plastic bracket during my last track weekend. Does anybody know the specs (thread, size) of the little screw? I am sure I could order one from the dealer; however, it would be faster and likely...

Got back from a 100 mile blast this afternoon to discover the bolt holding my seat in has disappeared! Can anyone confirm the size? I'm guessing a domed m6x25 or something similar. I can get 10x off Amazon for £2 or no doubt pay ducati £10 for one!

I'm doing the entire drivetrain. Why not; I'm almost at 2000 miles, time for a change :P most of the parts are already in; just waiting on a couple stragglers. Here's what I've got: - Afam 15T 520 steel front sprocket - Afam PCD-4 sprocket carrier (black) - Afam 41T 520 steel rear...

Hi guys I hate the 2 indexing screws of the rear swingarm pivot of my SL, ugly as hell! I'm pretty sure they are the same on all Panigales with the adjustable single side swingarm. Anyway, since I couldn't find any manufacturer, I'm going to make them in Titanium for myself. If anybody...

This is the ugliest screw I found on the pani. Zinc plated M8x12 (!) Who knows of you where the screw is mounted? The first one that gives the correct answer gets a replacement I made today (INOX, half the weight of the OEM screw).

Hello, I was wondering if any of y'all could save me a the hassle of making a bunch of trips to Home Depot. What are the specs of the screw I lost for the rear brake reservoir (see below)? Thanks! https://www.dropbox.com/s/jhytkza15in3ben/2014-08-15%2018.44.29.jpg

I kind of made a right mess of things when I stripped the bike of its front, side, lower side and rear fairings and when I decided to put it together every thing went back into place but for some reason I am left with a screw I cannot find the location for - I have literally no idea where it...

Hey guys. So my rear insert seems to be completely stripped on the opposite side of the swingarm for my rear mudguard. Just that one screw above the exhaust. Any suggestions on how to proceed? I'm at a loss.