switch

Hi I've just fitted a new CNC Left Handle bar switch to my V4s Streetfighter and after a few hours of riding it stopped working and the hazard lights remain on. I looked at the 6 pin connector and wiggled it a bit and it started working again and then it stopped working again. My problem is my...

I am switching out the brake and clutch master cylinders on a V4. And I wanted to keep the brake/clutch switches for street use - I found the aftermarket switches for the Brembo pumps I am using. I didn't want to butcher/splice the stock electrical connectors or touch the bike wire...

I have an 09 848 that is having toggle switch trouble. When I press down I can switch between trips and mileage. When I press up to go through the menu nothing happens. I tried replacing the entire switch assembly but the problem persists. The wiring harness is stock and I checked all the...

Some the HSBK the other day about there kill switch they make for the V4 however, they will not ship anywhere in the state of Oklahoma all because they don't want to pay taxes in the state. Anybody here in the group mind ordering me the part have it ship to you and than ship it to me. That is...

Anybody know if the brake light switches have any link to the ABS? Was thinking of using the front switch circuit as handlebar mounted rain light feed. Was unsure if the switch for lever pull had some other "logic" connection in the ecu or if it was purely a light trigger.

Bought a tether kill switch for my 2015 1299s The aftermarket kill switch has 2 wires that run through the pull out block. I understand I need to cut one wire and run it threw the aftermarket kill switch but I quickly took apart my right handle bar switch I found 4 wires hoping to find two...

Howdy all, I'm considering installing new switches to my 1299, does anyone have recommendations on brands, also has anyone used the switches that apex racing advertised on the forum a few months ago. Thanks

Hello, I installed the woodcraft rearsets on my base model actually I have only installed the brake side so far. I have the pressure activated light switch for the rear brake but the instructions are not quite clear or I may be missing something. Anyone ran into this before and how did you fix...

Banjo bolt brake switch M10X1.0 [Most Brembo] $21.95 These are great when installing aftermarket rearsets. Simply replace your banjo bolt on your rear master cylinder, then wire the switch to your to factory place. * FREE continental USA shipping on orders over $100. *...

Hi guys. Need a favour. I am looking for a wiring diagram for 1299 left hande bar flipper switch. That quick change up and down thingy. I have the full wiring diagrams for 2015 1299 base and S models but that switch is not mentioned there. I would appreciate a picture of the plug that it uses...

Yesterday on my ride I had my bike just shut off on me after coasting to a stop and putting the bike in neutral the bike started right up and stalled again as soon as I put it in gear. I then noticed the kick stand warning on the dash. The nut had worked it self off and the bolt backed...

Banjo bolt brake switch M10X1.0 [Most Brembo] $21.95 These are great when installing aftermarket rearsets. Simply replace your banjo bolt on your rear master cylinder, then wire the switch to your to factory place. * FREE continental USA shipping on orders over $100. * Outside...

For those of you that have WoodCraft rearsets, what did you do with the existing brake switch?

Can someone please make a tutorial on how to make and install a fan switch if possible? It would be great if its not expensive. Thanks.

Fitted new auxiliary Up/Down switch on left handle bar to control dtc, dwc, ebc. Cannot get it to work. Is supposed to work in race mode. Has anyone had this problem.

Does somebody know where the connector for unplugging the up/down paddle switch is located? (before I need to complete strip the bike..) I tried to follow the cable but its hard to see.. It seems to disappear left underneath the tank somewhere..

1199R/ 1299 Panigale

I have a question??? I recently had a little get off on my 1299S (a high side) at about 60mph and after launching my long ass in the air and landing in the middle of the track the bike slid on its side about 12 feet of pavement across the track then ended up in the grass. :eek: After...

Lowsided at the track last week. Bike came out of it really well, just a scratched fairing and the clipon tube snapped. Everything remained intact, just a scraped bar end. Today I went to start the bike up, turned the key, pump primes and everything is normal. Hit the starter button, nothing...

Hi all! I'm trying to change the rear brake switch, but the bolts going through the cover has some kind of back washer on the bolt which seems like it's fixed to the threads of the bolt somehow. Any tips on how to get the bolts out so I can place and fix the new wire?