wire

Anyone know where I can get Front and Rear Axle nut for 899 Pre drilled for Safety wire?

Besides just buying bolts pre-drilled anyone drill their own? Is it worth it? Any recommendations on brand of drill fixture & bits? Thanks

Hey guys, what redundant wiring can I literally chop off with out upsetting electronics on my race bike? Mostly the rat nest in the nose cone .:confused:

Want to delete the ABS pump. Figure i try this option first. The bike is set up as a race bike and ABS is not needed. Thank you Jimmy

Ok...dumb question here, but I couldn't find it and can't figure out how to route my headlight wiring. I wish I would have taken a picture before disassembly, but since the dealership has taken 2 months to get my forks rebuilt, I am trying to reassemble without having disassembled recently...

as required by all race organizations and recommended for trackdays: fork pinch bolts with extra jacket to elevate them out of the fork base, for enabling clips or direct safety - wire. as with the others, i need at least 10 sets committed to make this work. here's the design for the base...

Here is a good one"¦This is one I can't figure out"¦. Last couple of months sporadically my demon red princess would throw an engine code under WOT, couldn't figure it out and it would reset when bike was off then on. No time to drive it to dealer, and it only happened a couple times...

A couple of guys on this great forum showed some interest on the topic "safety wiring". So I thought let's start a new thread about this. First some basic rules: Do not kink, nick or mutilate the wire. Use some high quality INOX bright drawn steel (sorry, in german it's called "blank gezogen"...

My bike will never see a public road so I was wondering what I could trim off of my wire loom to clear up some clutter?

Is this the normal routing for this wire on a 2014 S? Thanks in advance! - Seth

do either. that spring isn't strong enough to hold the butterfly open at full power. I was *planning* to do it but didn't get around to it. that just wasted an hour on the dyno :(

I want to install a small phone charger for when the phone is on ram mount. How can I tap in to a hot wire to turn on with ignition?

Drilling front axle nut for safety wire Haven't found a drill guide that could accept a nut as large as necessary, and no one seems to be producing an axle nut that is already drilled. Aside from just freehanding it, anybody have better leads/ ideas for me? Thanks B

Wired mine this past weekend at Chuckwalla...just ran the wire to the plastic molding 2 inches from the plug. Is there a better anchor? Any pics? Also, to wire the caliper bolts...are you using aftermarket bolts instead of the round-headed stock ones?

Hi everyone. I have a base Pani with the Marzocchi Forks. I want to safety wire the front axle pinch bolts but the bolt heads are recessed into and flush with the fork bottom. Are there M6x25mm bolts that have a 10mm tall head so they will stick out and I can drill and safety wire them? Any...

Okay. So I finally decided to pull the left panel and attempt at installing my battery tender 12v dc charger. I'm mounting it to the rear mono shock and then running the wire through the new heat shield wire cover and will connect to my charger terminal zip tied to the clutch cable by the...

-- a buddy of mine (on his Aprilia RSV4), just had his Throttle Position Sensor (TPS) go full on - the motor rev'd up to redline (not sure what the rev limiter roll was) but it easily created a very dangerous situation......he managed it ok (pulled clutch in), and was able to stabilize it...

Good Morning, So while riding the Panigale the other day I started to think about how much throttle turn this thing has and reminded me of how my ZX-10 (cable throttle) use to have the same issue. The Ninja guys have a handy little "upgrade" which drastically decreases that travel which made...

Im from the old school and I currently use safety wire on all of my grips, but I am thinking of not using it on the new grips i just bought (Pro Grips). The Bike just looks so clean to have safety wire on the grips. I just wanted to get an opinion from the forum if you use safety wire the...

Mine did on the rear sprocket flange bolts. I guess I did get a little bit extra for the $341.48.:rolleyes: