wiring

After installing new high-tension coils & testing the other components of the ignition system, I am now unsure of the electrical connections. (I know...I should have taken photos)! Since installing the new coils, the engine won't fire & emits a deafening backfire. So, it seems to me that I must...

Hi guys, I picked up an 1199 at auction recently... which is to say, I had no contacted with the previous owner and had no idea what's been done to it before I got my hands on it. I've sorted out most of what needed sorting and found it has a Bazzaz tuner, integrated tail light, and some...

Hello all, Disclaimer: I have absolutely tried the search function... I can not seem to find a source for the set of blank-off plugs that (i assume) normally come with the DP Race Fairing kit. I'm purchasing Sharksinz and would like to use the proper blank-off plugs for the kickstand...

Bought a tether kill switch for my 2015 1299s The aftermarket kill switch has 2 wires that run through the pull out block. I understand I need to cut one wire and run it threw the aftermarket kill switch but I quickly took apart my right handle bar switch I found 4 wires hoping to find two...

Hi all, my bike has track plastics and instead of switching everything off to revert to street fairings, I went ahead and purchased a small LED tail light off of ebay. Figured I could pop it on and off as needed. The wiring is simple, 5 wires. One for running light, brake, left blinker, right...

Never mind. Thanks.

Fellow Members- Well, by now those of yoo's guys who go out Club Racing have either put in some laps already or prepping for the first race of the season. God I miss it guys! Spent over 6-7 yrs doing that stuff and unfortunately now, I'm too broken myself. I'd never say "Too Old" because Im...

Can someone post picture or video on how the electronics should look like behind the main fairing underneath the fuel tank. On both sides please, I replaced the thermostat unit just want to make sure it goes back together how it should.

I just received my new innovate LC-2 kit, not from Tuneboy which apparently is modified to plug and play. I can't seem to find anything on line which shows the prepare wiring, has anyone faced this? Is there an aftermarket plug to buy? Or an wiring scheme online somewhere that I'm missing...

OK, had my O2 sensors unplugged (its complicated). Which O2 sensor goes to which plug? have a 50/50 chance but figure I would ask if someone could help me out. Thinking the rear O2 sensor wire goes to the plug behind the ECU, and the front O2 goes to the lower connector. Any help would...

So, I am reassembling the fuel delivery system (shower heads, injectors, etc) after changing the air filter and the "before" picture I took is not good enough to determine which of the two injector wiring connections goes where. One is labelled "INJ top V" and the other is labelled "INJ top...

Does anyone have a good RECENT source for pre-drilled bolts for our bikes, so I can safety wire my bike? I HATE drilling bolts for safety wiring and if I can buy them ready to go, I would prefer it. Cheers.

Has anyone wired their low beams to stay on with their high beams? If so, any issues? and how did you go about wiring them up?

Hey, I am about to do the 1199S LED headlight conversation to my base model, i just have a question regarding the wiring. I am using the following wiring diagram (i believe a forum member made) My question is regarding the relays wiring 1] Yellow/Gray (relay) to Yellow (headlight)...

Hi everyone, Has anyone replaced their injector wiring harness? I've cracked the main plug connector on my injector wiring harness and I want to replace it. I don't know how to remove the plug from the airbox and install the new one. There is nothing in the workshop manual. Any help? Cheers...

Ducati Trieste replaced my run (kill) switch wiring and maybe the switch inside the housing, they said it was a Ducati instigation, maybe others should check out if you haven't already, I didn't have any problems with it but OK they wanted to change it and I didn't pay! Sorry guys edited it to...

There are a bunch of threads here asking about the various plugs to terminate the wiring for vaious items like the tail lights, ignition and side stand. could we post a list of available parts on one thread and maybe make it a sticky? maybe include any instructions, tips or tricks? I'm setting...

Hey guys, just purchased my first Ducati, a 1199 standard model! I made my own fender eliminator and had opted out to use the auxiliary light. I was wondering if anybody has thought of using that wire and splicing it to use it as a charger for mobile device? i.e. iPhones or Galaxies. The space...

I may be selling my LED headlights and wiring harness. Is it possible to remove the wiring harness without affecting the rest of the electronics? What do I have to remove? Thanks

I had my bike upmapped, first service, and heat shield last week. The past week I rode it to work and back. No issues in the cool morning but on the way back home with 90 degrees and sunny, the engine got to about 210 degrees F. The right turn signal stopped working and the left odometer...