Bar End Mirrors

Italianonegro · Jul 20, 2014

Abe end mirrors

leftcoast32 said:
I picked them up at a local Cycle Gear. They cost just under $50.00 for 2 of them. They come in Black or Silver anodized.

Where did you relocate your indicator signals?

leftcoast32 · Jul 20, 2014

Italianonegro said:
Where did you relocate your indicator signals?

I am going to install LED turns inside the headlight. Then I will put an integrated taillight on with the LED turns inside.

Italianonegro · Jul 20, 2014

Ok, cool.

reganc · Jul 20, 2014

leftcoast32 said:
I am going to install LED turns inside the headlight. Then I will put an integrated taillight on with the LED turns inside.

Look at the Oberon turn signals I use the with the crg mirrors and it's a very clean look

leftcoast32 · Jul 20, 2014

reganc said:
Look at the Oberon turn signals I use the with the crg mirrors and it's a very clean look

Thanks! I will just do the headlight mod for them. It really isn't to hard, just need to take the time to do it.

leftcoast32 · Aug 9, 2014

I added the DP Race Seat and DP Carbon Termi Heat Shields.

The DP Race Seat worked out really nice for me. I sit all the way back on the seat and was sliding forward into the tank on hard braking before corners. The DP Race Seat helps by having better grip and the front is raised to keep me back on the seat. Great Addition!

The DP Carbon Termi Heat Shields are a very nice visual addition to the other carbon so far.

Tyler1199 · Sep 30, 2014

So can you get the stock bar ends to work with the arrows?

RSR racer · Sep 30, 2014

zaster said:
I'm glad you opted to get rid of the ugly insect antennas.
These are a tad more pricey but give an increased field of view:

Have same set. Fantastic product and great visibility.

zaster · Sep 30, 2014

still very happy with it after 8K miles

Tyler1199 · Oct 1, 2014

Well if your happy with them help a brother out haha can you use them with stock bar ends? Is there anything else that needs purchased with them to install

marky mark · Oct 1, 2014

reganc said:
Look at the Oberon turn signals I use the with the crg mirrors and it's a very clean look

Those oberon turn signals look pretty cool, how the hell do you route the wiring? I assume down the inside of the bars, but where does it come out, and do they connect to the original connectors?

reganc · Oct 1, 2014

marky mark said:
Those oberon turn signals look pretty cool, how the hell do you route the wiring? I assume down the inside of the bars, but where does it come out, and do they connect to the original connectors?

Honestly I have no idea I always get these added when I buy a bike and the dealer just sorts them out for me, but they are a great addition

topolino · Oct 1, 2014

marky mark said:
Those oberon turn signals look pretty cool, how the hell do you route the wiring? I assume down the inside of the bars, but where does it come out, and do they connect to the original connectors?

You normally route the wires out through the ends of the handlebars and connect them to your stock OEM connectors. I fitted Rizoma fluid reservoirs so I had to drill a small hole in the bars and run the wires out that way, since the reservoir brackets fit into the handlebar ends. I bought the OEM connectors from MotoWheels and spliced these onto the Oberon wiring, soldered them together and finally covered the connections in heat shrink tubing. I've included some pictures, if these prove of any use to you.

marky mark · Oct 1, 2014

Thanks very much, think I'm going to go this route

zaster · Oct 1, 2014

Tyler1199 said:
Well if your happy with them help a brother out haha can you use them with stock bar ends? Is there anything else that needs purchased with them to install

The picture you see has the mirror mounted on the left handle bar with the stock bar ends in place. You do need to slide the grip in by about a 1/2 inch and it will fit right on as is.
I'm using only one mirror and for the right side you would need different bar ends to make it fit.

Gecko · Oct 2, 2014

topolino said:
You normally route the wires out through the ends of the handlebars and connect them to your stock OEM connectors. I fitted Rizoma fluid reservoirs so I had to drill a small hole in the bars and run the wires out that way, since the reservoir brackets fit into the handlebar ends. I bought the OEM connectors from MotoWheels and spliced these onto the Oberon wiring, soldered them together and finally covered the connections in heat shrink tubing. I've included some pictures, if these prove of any use to you.

Could you show how you mounted the fluid reservoirs?

topolino · Oct 3, 2014

There's a picture on the website, on the Stages In Progress page. Look under Hydraulics.

Bar End Mirrors

Help Support Ducati Forum:

Italianonegro

leftcoast32

Italianonegro

reganc

leftcoast32

leftcoast32

Tyler1199

RSR racer

zaster

Tyler1199

marky mark

reganc

topolino

Attachments

marky mark

zaster

Gecko

topolino

Similar threads

Register CTA

Recent Discussions