Tune my 1199 standard

jabba29 · Jun 25, 2012

Hi,i am a little frenchie(its for my bad english

) ,i would like to tune my 1199 standard with a new scheme based on vinyl covering.But i would like to have your suggestion or idea or a photoshop picture..
I have seen this model (corse) that i like a lot but i tought maybe someone has a best idea to upgrade the "corse line" to the 1199 agressive and modern line..Already thankx for reading me,best regards

tstephenson · Jun 25, 2012

jabba29 said:
Hi,i am a little frenchie(its for my bad english ) ,i would like to tune my 1199 standard with a new scheme based on vinyl covering.But i would like to have your suggestion or idea or a photoshop picture..
I have seen this model (corse) that i like a lot but i tought maybe someone has a best idea to upgrade the "corse line" to the 1199 agressive and modern line..Already thankx for reading me,best regards

Looks good to me

Braintrash · Jun 25, 2012

Easy. You take the white part on the belly and turn it black too.
(Tu peins aussi toute la partie sabot en noir ; tu ne gardes du blanc qu'autour de la lignÃ©e rouge.)

Also, take a good care to have a very deep black done.
(Tu fais attention au noir, qui doit Ãªtre bien profond ; le rouge, tu reprends le rouge Ducati.)

husker1 · Jun 25, 2012

jabba29 said:
Hi,i am a little frenchie(its for my bad english )

No need to be apologetic - wait until you hear our French. I learn most of mine from the French cop drama "Engrenages" or as the BBC has it, "Spiral".

My French swearing has greatly improved...

Braintrash · Jun 25, 2012

PaddockStand · Jun 25, 2012

Braintrash said:

Prefer the first one.

flobrandx · Jun 25, 2012

I'll take the original. Nice design!

Delta One · Jun 26, 2012

I love the original! However I get the point about making the bottom black, as white will be a PIA to keep clean.

So my suggestion is to make the bottom black as mentioned above but then lower the white and red part on the front/side fairing by about 10 centimetre.

Keep the white and red line on the rear fairing and tank where they are now, looks good.

Just my 2 cents !

Phl · Jun 26, 2012

what happened to the fender?

jabba29 · Jun 26, 2012

Delta One said:
I love the original! However I get the point about making the bottom black, as white will be a PIA to keep clean.

So my suggestion is to make the bottom black as mentioned above but then lower the white and red part on the front/side fairing by about 10 centimetre.

Keep the white and red line on the rear fairing and tank where they are now, looks good.

Just my 2 cents !

thnx to all for your idea

If i well understand , i put white and red part 10 cm down..So on tank i will have only white no black..
like this for the side part (need to complete rear part and front)

And do you think if i keep tank red instead of grey?

For the black part i don't know which is best choice..
-Black in gloss vinyl (like on 1198 corse,the black is gloss)
or
-Black will be carbon vinyl (matt)as the picture

The bottom will be hard to keep clean in white

Justifire · Jul 1, 2012

White and black line running over the underside of the tank give the bike a much more speedier look.
I would also make the white striping thicker/higher at the front as far as it match the 'visual line' the 1199 panigale text is in.
Swap the front fender with a carbon one and it will look sick !
Maybe change the belly pan from white to red ?

jabba29 · Jul 1, 2012

A picture to illustrate that?

Kman · Jul 27, 2012

I love them both! Actually just emailed a local painter for an estimate about doing the Corse scheme. Was going to do it to my 848 EVO before rumors of the 848Corse was thought of.

Tune my 1199 standard

Help Support Ducati Forum:

jabba29

tstephenson

Braintrash

husker1

Braintrash

PaddockStand

flobrandx

Delta One

Phl

Moderator

jabba29

Justifire

jabba29

Kman

Similar threads

Register CTA

Recent Discussions