brake

It's been brought to my attention that the stock brakes on my 899 are pretty spongy. Upon feeling the fellow rider's brake lever, it was like a rock (yea, that doesn't sound right, just go with it). I did a brake flush on the bike when I got it originally and felt that the brakes were about the...

This is something that has had to have been asked before but, I have been searching the internet for the answer and can't seem to find what I am looking for. I am looking to upgrade my front brake rotors to Braking's latest rotor. However, the newest rotor released this year is only available...

Any ideas ? My rear brake reservoir looked like it has coffee in it, and the front wasn't much better. I took it back to the dealer and asked them to flush the system & bleed the brakes. They did so in what I thought was perhaps a suspiciously short time, given all the ABS system. Rear has...

Stumbled upon those things, those duct type things that fit on the front brakes that should channel air to the brakes? Are those things for real and if so what would the efficiency be? I find no tangible info regarding their cooling capacity and efficiency and I tend to think those are more...

Is anyone using this by chance? Thumb 11 | Master-cylinders | Racing | Motorcycle Brakes Configurator

Sold Sold

Sequential Module/Brake Light Modulator for Stock Brake Light Hello. Who has a module that can make the stock brake light sequential? I tried a module on the RSV4 and it worked. I tried the same module on my 1199R and it seldom did sequential and eventually gave me a Brake Light Error, more...

Just back from a ride and noticed the Brake fluid spilled all over the windscreen and the instrument panel display. Noticed the reservoir cap came loose and had it tighten it by hand. Even though I wiped it off as soon as I noticed, it looked like the brake fluid already ate through the plastic...

Hi there all, Just checking to see if anyone has had a problem like this, or could point me in the right direction! My 1199S recently decided to spit it's rear brake assembly off (whilst being ridden) via the metal fracturing through the MIDDLE of the carrier. There was no prior damage and...

Anyone swapped to a different brembo brake master yet? Just sourced some V4 panigale Stlyema calipers and was told the RCS 17x18/20 would be the ticket, which i have on hand. Putting these on my MV Agusta F3, and (EDIT) 4 30mm pistons, perfecto.

I recently started rebuilding the 1199 race bike back to original so it can operate again on the street. However I found two issues which gave problems. First was the left handlebar switch which didn't operate 100%. This was luckily solved by installing a free new service wiring part in the...

Just a reminder to check your rear brake caliper and let your dealer know if your clutch slowly loses feeling. I've been having to bleed air out of my clutch every couple hundred miles, no big deal, but apparently there was a bulletin put out less than 24 hours ago about that issue. Also, my...

Brembo Rear Brake Caliper w/Pads Ducati Part 611.4.029.1A Fits SBK 1098/1198 STREETFIGHTER 1098/1098S + Many more! Streetfighter S Takeoff w/ 252 miles Perfect working condition NO scratches, blemishes, or rash whatsoever Pads are full with barely any use $75 Shipped PayPal...

Hi All, I had to upgrade to Brembo RCS 19 master brake cylinder yesterday at the track as my original went bust. (Interesting side note if some 1199 rider didn't know - like myself: it is a fault that Ducati addresses in and beyond(!) warranty, so I am now waiting for their response expecting a...

Hi all, Does anyone have measurements of the hub and the brake caliper fitment? I'd really appreciate to find this data or to receive advice on where it can be purchased. Many thanks in advance, ele

I had this problem while building the 1199 track bike, and now that I'm transitioning the 899 to a track-only bike I've got the same issue. My brake reservoir hits the windscreen and nose fairing really badly. Does anyone else have this problem and how have you dealt with it? I've...

Anybody knows the torque specs for the bleeder valves (master cylinders and calipers) front and rear?

Seriously, I'm tired of bleeding this clutch system every time I ride the bike. What is the compatible Brembo part number to replace this factory junker? I would even replace the brake master while I'm at it.

while riding yesterday, at one point I applied the rear brake only...and there was no tension on the foot lever, as if all the hydraulic fluid had drained out. That's probably not good, so I pulled over, tried the rear brake again, which then had normal tension and worked fine...except for a...

I’m trying to get some feedback on the CNC Racing PRAMAC Carbon Fiber GP front brake cooling ducts. I’m considering them for my track bike. Anyone using them? rWxr1MzL2bI