fork

Hi all. Anyone was replacing fork legs on 1199? I have checked the Ducati workshop manual and based on that seems that is impossible to replace legs in garage conditions??? It requires 0.1 mm accuracy (see attached pic). So, I don't know which tools I should use to get same accuracy...

I had a question regarding fork installation. I picked up some Ohlins Fgrt's and wanted to do the install myself but I had a question regarding the orientation when you mount them in the triple clamp. Is there a specific orientation they should be mounted in or it does not matter because the...

Hey whats up guys, the forks on my 1199 (2013 base model with Marzocchi Forks) are leaking so I'm going to try and see if I can change them myself. Does anywhere know of some places that I can buy the correct fork seals for my the base model that has 57mm Marzocchi Forks? I've been having...

ATHENA Front Fork Seals [Showa Forks Only]: Ducati Showa Forks [Early SBK, Monster, ST] $13.95 High quality replacement fork seals Made in Italy Seal Dimensions: 42mm ID 54mm OD 11mm Thick ATHENA Front Fork Seals [Ohlins Forks Only]: Ducati MTS1200, Streetfighter S...

Anybody know how I could go about trying to find some fork cables for my 1199S? eBay didn't turn anything up, maybe my search terms were off...

I've had a nightmare of a time with my local dealership and getting my fork rebuilt. -fork seal was leaking -12/20/2016 took the fork into the dealership -pitting on lower fork tube, need to replace it to ensure no more leaking -ordered $350 part (has to come from Sweden) -2/3/2017...

ATHENA Front Fork Seals [Showa Forks Only]: Ducati Showa Forks [Early SBK, Monster, ST] $13.95 High quality replacement fork seals Made in Italy Seal Dimensions: 42mm ID 54mm OD 11mm Thick ATHENA Front Fork Seals [Ohlins Forks Only]: Ducati MTS1200, Streetfighter S...

as required by all race organizations and recommended for trackdays: fork pinch bolts with extra jacket to elevate them out of the fork base, for enabling clips or direct safety - wire. as with the others, i need at least 10 sets committed to make this work. here's the design for the base...

Hey all, i tried to search and didnt come up with anything useful. I need to know how to remove the stock forks off my 2012 base 1199 because Im going to pickup a set of Ohlins FGRT 203 Nix forks and would like to do the job myself. It doesnt seem too hard but a DIY would be helpful. Also if...

ATHENA Front Fork Seals [Showa Forks Only]: Ducati Showa Forks [Early SBK, Monster, ST] $13.95 High quality replacement fork seals Made in Italy Seal Dimensions: 42mm ID 54mm OD 11mm Thick ATHENA Front Fork Seals [Ohlins Forks Only]: Ducati MTS1200, Streetfighter S...

One of my forks is leaking pretty bad and I need to get it repaired. Called my local dealership and they want $125 per fork for the seal kits and 3 hours of labor which comes out to around $550-600. I found the seal kit on Kyle Racing's site, but I want to make sure it's the right one. Also...

hello Anyone give me any advice on removing the fork splash guard. Two alen bolts at the back no problem to remove, but there's one remaining one, but its covered by the horn (circle below). So you have to get the horn off first , and there's no way I can get a spanner on the horn nut...

ATHENA Front Fork Seals [Showa Forks Only]: Ducati Showa Forks [Early SBK, Monster, ST] $13.95 High quality replacement fork seals Made in Italy Seal Dimensions: 42mm ID 54mm OD 11mm Thick ATHENA Front Fork Seals [Ohlins Forks Only]: Ducati MTS1200, Streetfighter S...

Anyone upgraded their 50mm Marzocchi fork with some other springs? Which kit is recommended? Thanks.

ATHENA Front Fork Seals [Showa Forks Only]: Ducati Showa Forks [Early SBK, Monster, ST] $13.95 High quality replacement fork seals Made in Italy Seal Dimensions: 42mm ID 54mm OD 11mm Thick ATHENA Front Fork Seals [Ohlins Forks Only]: Ducati MTS1200, Streetfighter S...

So Like a lot of you I have run into the loss of rebound damping on the base Marzocchi forks. I have had Racetech, Ohlins, and K-tech on other bikes. Befor my Pani, I had a 1098 base that raced and street rode that I had converted to Ohlins. So I have ridden with more that one brant or modified...

Motion Pro Fork Oil Level Gauge Pricing: $22.95 For checking and adjusting the oil level on all conventional and single chamber cartridge forks. Adjustable ring will measure oil levels from 0 to 300mm in 0.5cm increments Syringe has a capacity of 60ml Motion Pro Ringer Fork Seal...

Hi friends. I was reading many posts here but did not find clearly answer. That's why I am creating this thread. Please watch my video and advise what can help me... I don't want to replace a fork... My Panigale has about 600 miles only. Are there ways to fix it w/o fork replacement...

I have a 899 with Ohlins Road&Track 30mm front fork cartridges. I am in the process preparing my 1299 race bike. My plan is to use the forks including the triple clamp from my 899 and use on the 1299. Is this possible to do?

Motion Pro Fork Oil Level Gauge Pricing: $22.95 For checking and adjusting the oil level on all conventional and single chamber cartridge forks. Adjustable ring will measure oil levels from 0 to 300mm in 0.5cm increments Syringe has a capacity of 60ml Motion Pro Ringer Fork Seal...