issue

I have 3 bursig lifts for my S1000RR, S1000R and just got one for the 1299. Im having an issue with the one for the 1299. Once I fit the plate adapter on the bike to adjust the lower floating pin on the plate I move the plate back forth to make sure it slide on and off the bike. I then tighten...

Does anyone know if the carbon heat shield is covered by any kind of warranty? After the track yesterday I noticed where it looks like it's getting thin or something and shapes are appearing in the shield like it's melting down in certain spots. Sent from my SM-G930V using Tapatalk

I have an issue with my 2015 1299. I recently bought it with 1700 miles on it. I took it out for a quick spin before I put it on my trailer and drove it a few hours back to my house. The quick spin was for about 10 miles and regular shift pattern was the setup. I don't recall any shifting...

Hey all I posted this in the technical section but got 100 views and no replies so I'm posting it here too. Trying to figure out if I have the wrong part or missing a spacer or something like that..... I have a question about installing this quick change carrier I bought. It seems that on...

Hi All, I have a question about installing this quick change carrier I bought. It seems that on the backside of the carrier it is recessed so that the sprocket sits too far back against the hub. When I look at the OEM piece that came off it seems to be more flush all the way across the back...

I am very sensitive to vibration in the clip ons, but every bike I've had I have been able to fix it or make it good enough for it not to bother me. The 1299 is different, and it took more drastic measures to get it under control. But here is what I did 1) Gel Grips - this always helps. I...

Hey guys had the check engine light come on today. Here's a quick summary of events. Been riding the bike for about a half hour with no issues and pulled into gas station and filled the bike up with gas (only needed half of a tank to top if off) then rode about 10 miles and the engine started to...

I have a 12 1199 triclore. The running tailight is working but the brake light does not work from either lever. I pulled the rear off and there is the one 3 wire connector going to the lights. I made sure it was seated well, could not get in unplugged and didnt want to break the connector. I...

Hey all, Apologies in advance if this thread is not in the right spot. Hopped on the bike this morning and, for the second time, the clutch lever went practically all the way in to the bar before I hit the friction and full disengagement zones. The normal feel and engagement zone comes...

Just wondering if I got a defective part or this is actually a common issue with DP parts. I have a ducati performance Billet aluminium clutch casing cover 97380361A. When I tried to install it, I noticed that the screw that comes with the kit does not fit straight through the holes of...

I just fixed a problem I had with a bad TPS that I thought I would share. Bike: 2012 Ducati 1199 Problem: Once the bike would warm up, the throttle would get very choppy and then the bike would cut off and the red engine light would turn on. I could let the bike cool down, and start up again...

Hi, I'm looking for some input in regards to installing a full up termi exhaust up map onto my 1199 base. I bought the full exhaust about a year and half ago and never got to install it until this weekend. I have the full exhaust installed and when I try to install the up map - I get a...

Hello all, New member here but long time faithful Ducati.ms member (same handle). The good news: I recently purchased a 2016 1299 with 2,000 kms on it. Bike was cosmetically new and ran like new...until today. The bad news: After giving the bike a full once-over to ensure that the...

Hi guys Had an off and the bike now has the eobd light on. I know I can go to a dealer and for £75ish get them to diagnose the problem but just thought I'd make sure its nothing obvious. Initially there was an "eng" error code on the dash which was the air temp sensor unplugged after the...

Hello all, Does anyone else find that the DP race seat causes excessive pressure right between the inside of your legs and butt, right in the area just beside your groin? I'm thinking I may have to ditch the seat and go back to the stock seat as I have put several hundred miles on the race...

To Pin Point the DQS issue, I will make some facts and assumption to delete the possible cause: Facts: 1. When I fell in the garage, bike landed on my leg (bike never touched the ground) but I believe Rearset was on my leg and when I picked it up, I saw scratch on the Swingarm where Shift...

Hey guys I have a bit of a problem. So I installed a set of CNC rear sets and a set of CNC adjustable levers. Now the ABS isnt working and neither is the quick shifter. The abs warning light is on and another warning light is on. Could I have installed something wrong or did something else...

I know this topic has been discussed on here, I mentioned to my dealer it's been said that disconnecting the cable from the servo may reduce heat build up? He says no it will make no difference? And it may throw a code? Guys what's the consensus to removing the cable from the valve ? I see the...

Hi Guys, my 2012 bike with 5000mls was in for a fresh Oil change for the new season at the local Ducati store (have it second hand since end2013 at 1600mls). Dealer mentioned 'bike is not running smooth' after the test ride. Didn't notice anything myself last year, honestly. Looks as running...

I forgot where I read it, but is it true that Ducati 1299s's clutch cover is made out of magnesium alloy? If that's true, has anyone that uses ducabike clear clutch cover experience any galvanic corrosion issue with the aluminum cover on the magnesium housing? I believe they are .7V's away...