LAP EVO

roadracerx · Aug 15, 2023

So I am reading through the manual for the 2023 V4R and I see this on page 151. My V4R, I assume like all others, comes with the GPS receiver on the bike and a DDA USB dongle in the box of accessories.

What I don't understand is the sentence below..."If the bike is equipped with the GPS EVO module, the LAP EVO function is enabled."

On the previous page of this same owner's manual there is some information about LAP BASIC with GPS module.

Is the LAP EVO something that is included with all V4R or an add-on?

KarlKani · Aug 15, 2023

It's included with all V4R, frustrating that you have to do a long hold for the splits. All other after market data setups you can signaled those splits after the fact

SuperDomestique · Aug 15, 2023

How would you realistically set intermediate splits? Sounds like you would have to stop on track to mark the coordinates

roadracerx · Aug 15, 2023

SuperDomestique said:
How would you realistically set intermediate splits? Sounds like you would have to stop on track to mark the coordinates

Yikes!

Seth Vo · Aug 15, 2023

Is this not similar to setting the finish line by pressing the flash but it looks like it allows you to set two more point on the track? Probably a pain to set it on the first lap

but then would allow for splits for the rest of the day at a more granular level...?

Alkhater · Aug 15, 2023

Split location is just for reference, it doesn’t have to be an exact location as long as it’s the same every lap.

I don’t see a problem with it having to be a long hold (probably 2 seconds?) while passing the split locations on the first lap. Definitely not ideal but not that big of an issue.

Somefun · Sep 6, 2023

Guys this is one that I’m trying to make it work and having a bit of an issue with it. When I get out I have it in race mode one then make a lap and pull the trigger to set the starting point. I make my lap and it doesn’t seem to make the next lap and just keeps going. Is that because the first pull of the lap timer needs to be held for two seconds?

Taz · Sep 6, 2023

Somefun said:
Guys this is one that I’m trying to make it work and having a bit of an issue with it. When I get out I have it in race mode one then make a lap and pull the trigger to set the starting point. I make my lap and it doesn’t seem to make the next lap and just keeps going. Is that because the first pull of the lap timer needs to be held for two seconds?

No, you should only need to pull the trigger for the high beams once to set the starting point, but it needs to be done before you complete a full lap from where you enter the track, otherwise the GPS will use the point at which it registers that a full lap has been made. I think the two seconds only applies if you wish to add split sectors.

Somefun · Sep 6, 2023

Taz said:
No, you should only need to pull the trigger for the high beams once to set the starting point, but it needs to be done before you complete a full lap from where you enter the track, otherwise the GPS will use the point at which it registers that a full lap has been made. I think the two seconds only applies if you wish to add split sectors.

OK so best bet would be to pull the high been switch when your pulling onto the track from pitting out I would think? then the next lap will be a bit slower because your just getting on the track but then every lap after that should be in the memory? How do you stop the lap timer?

RickD996 · Sep 6, 2023

Somefun said:
OK so best bet would be to pull the high been switch when your pulling onto the track from pitting out I would think? then the next lap will be a bit slower because your just getting on the track but then every lap after that should be in the memory? How do you stop the lap timer?

Pull into the pits will stop it.

When you initially pull the flash button, try and be central on the track. Or, at a minimum, on the racing line.

Somefun · Sep 6, 2023

RickD996 said:
Pull into the pits will stop it.

When you initially pull the flash button, try and be central on the track. Or, at a minimum, on the racing line.

Ok sounds good Rick thank you! Last track days are coming up next week! looking forward to using it the proper way this time! lol

KA77 · Sep 6, 2023

Do you need to set the start / finish point on every session? Or once you’ve done it the first time does it remember

RickD996 · Sep 6, 2023

Set it once, and it saves it until overwritten

Somefun · Sep 6, 2023

Do you have to set the start / finish line and the two split locations if you don't want to? or can you only do the start finish line while using the EVO Lap?

yoshiboldor · Oct 18, 2024

Hi guys, I have a 23 V4S with lap EVO, my instructions do not mention doing short of long presses, it just says press. but regardless I really struggle to get the start finish in the right place and the splits. Anyone else figure it out?

LAP EVO

Help Support Ducati Forum:

roadracerx

KarlKani

SuperDomestique

roadracerx

Seth Vo

Alkhater

Somefun

Taz

Somefun

RickD996

Somefun

KA77

RickD996

Somefun

yoshiboldor

Similar threads

Register CTA

Recent Discussions

Recent Discussions