Termi UpMap D184SR Issues

Joined Mar 2021
45 Posts | 6+
Charlotte
Hey all,

Installed my black titanium Termi slip-ons on my 2022 Panigale v4s and went with the D184SR (without DB killers) and the bike runs like crap. It bounces during idle while warming up and at low RPM's (coming up to a stop light), it stalled at a red light and just doesn't feel right. Anyone familiar with this or know what's going on? Any solutions; re-install? Go with different tune? I know there's a guy who tuned my 1299 (I believe out of Florida) but can't recall who it was. Only other thing I did to the bike was install the sprint air filter and remove the charcoal cannister.

Thank you in advance!
 
Also, try uninstalling the map (you should be able to reinstall the stock map). Then see how the bike runs, and if OK, then retry the new map. Sometimes they don't install correctly.
 
Hey all,

Installed my black titanium Termi slip-ons on my 2022 Panigale v4s and went with the D184SR (without DB killers) and the bike runs like crap. It bounces during idle while warming up and at low RPM's (coming up to a stop light), it stalled at a red light and just doesn't feel right. Anyone familiar with this or know what's going on? Any solutions; re-install? Go with different tune? I know there's a guy who tuned my 1299 (I believe out of Florida) but can't recall who it was. Only other thing I did to the bike was install the sprint air filter and remove the charcoal cannister.

Thank you in advance!

When removing the carbon canister, did you plug the larger (about 8mm ID) hose that goes back to the intake? If not the engine is drawing false air and can cause issues like you are experiencing.
 
When removing the carbon canister, did you plug the larger (about 8mm ID) hose that goes back to the intake? If not the engine is drawing false air and can cause issues like you are experiencing.

Yes sir! Plugged it with a 8mm bolt.
 
  • Like
Reactions: cavlino
Also, try uninstalling the map (you should be able to reinstall the stock map). Then see how the bike runs, and if OK, then retry the new map. Sometimes they don't install correctly.

Yeah that's my next move. Appreciate it bud!
 
  • Like
Reactions: RickD996
Check and then double check the instructions to see whether it calls for unplugging of the O2 sensors.

It doesn't mention anything about removing on the directions but the upmap site does state:

"Lambda probe error disabled, it is possible to unplug connectors. Attention: If not removed, the lambda probe (Oxygen O2 sensor) continue to work, it is recommended to disconnect the connectors of all 4 sensors"

Do you know where the 4 sensors are? Weird that the exhaust instructions never mentioned anything about this.
 
Just to be clear, you installed the race air filter with the slip-ons? And try putting the baffles in. The computer also needs to adjust (run the bike a few times).
 
Just to be clear, you installed the race air filter with the slip-ons? And try putting the baffles in. The computer also needs to adjust (run the bike a few times).

Termi slip ons, sprint 08 filter, no baffles. I will re-install map and then run a few times and see. I've already ran the bike 3-4 times and same results
 
My UpMapp tune came with 2 profiles - one with and one without baffles. It apparently makes a difference. Cheers and good luck.
 
^ Correct. I've has my Termi 184's and the T-800 Upmap in for a while now. Rode on Christmas Day and noticed a little "fluttering" but nothing significant as far as revs go. Perhaps the Lambda sensors should be disconnected? Strange stuff for sure.
 
First thing I’d try is to re-flash the stock map.

IIRC, the O2 sensors only effect the bike near idle. They’re easy enough to unplug. I don’t have a EU5 bike so mine only has two sensors. I don’t remember there being a big difference with or without them.
 
  • Like
Reactions: JHTmcrider
Hey all,

Installed my black titanium Termi slip-ons on my 2022 Panigale v4s and went with the D184SR (without DB killers) and the bike runs like crap. It bounces during idle while warming up and at low RPM's (coming up to a stop light), it stalled at a red light and just doesn't feel right. Anyone familiar with this or know what's going on? Any solutions; re-install? Go with different tune? I know there's a guy who tuned my 1299 (I believe out of Florida) but can't recall who it was. Only other thing I did to the bike was install the sprint air filter and remove the charcoal cannister.

Thank you in advance!

I had a Streetfighter with termi slip ons and that upmap…took a couple of tries to get it to load properly.

Make sure you have a full battery and put the trickle charger on it, if the battery get too low it messes up the upload and can damage your ecu
 
  • Like
Reactions: JHTmcrider
Anyone got to solve this

Just installed mine, haven’t rode on it, but on the garage, idle goes up and down all the time
 
Engine temp, I think, has a big say in this. I'm of the opinion, or taking the stand, that cold idle doesn't matter that much.

If you start the bike and walk away until the fans turn on, how does it idle?
 
Right now it is up and down on idle all the time

Just moved the bike forward and it sounds good, but bike still on the shop, will get a chance to ride it tomorrow
 
One question for users of the T800 UpMap on 2022 euro 5 bikes

Do you get the RACING PRO sign on your dash, when starting the bike?

Mine doesn’t show it, after flashing the bike 2 times